Use a wood sanding block to prevent rounding over the wood edges (Image 2). In Back to Basics, we’re providing you with the straightforward step-by-step instructions to tackle all those household projects you’ve been wanting to try. Wood Veneer Cabinets: If your cabinets have a wood veneer—essentially a very thin layer of real hardwood over a pressed material—you will also need to sand before painting your kitchen cabinets.But before you break out the sandpaper or paint, carefully inspect the veneer for loose edges, chips, or cracks. Changing the color of your cabinets can make a somewhat outdated countertop look a bit more stylish and it can brighten up an otherwise dim space. Copyright © 2020 Multiply Media, LLC. For more details on how to properly strip your cabinets, including tips for determining their type of finish and the right products to use, see Refinishing and Cleaning Kitchen Cabinets. This kitchen renovation might be simpler than installing a new backsplash, but it does leave room for mistakes.

5. 12. Place the hardware in a plastic bag or cup and label where it goes. When you’ve covered the surface, take your dry roller or brush (don’t reload it) and lightly go over the surface once again to remove any buildup. Simply apply with a brush, wait for the stripper to react with the old paint, then use a plastic scraper to peel it away.

Check out our buying guides and how-to videos for help: Don't just take our word for it. Some liners are decorative and stick to the surface. 9. Special cabinet paints are available that provide a smooth finish, but any high-quality paint should work. After you have completed your cabinet refresh, this may also be a good time to install under cabinet lighting or even a new backsplash. They looked pretty bad and I wanted to do something that would help. On the cabinet doors and drawer fronts pieces, paint the backs, let them dry, then paint the fronts. How to Redo a Fake Wood Cabinet Surface. After cleaning, it’s time to roughen things up! Laminate paint requires a special bonding primer. Apply paint to the cabinetry using the same technique: Use a small roller for larger surface areas and a brush to cut into corners and details, starting from the back of the cabinets. Make sure to tape a drop cloth or another protector over the countertops and the surrounding work area while painting. Lightly sand the doors on all sides and faces (Image 1).

Others say it isn’t necessary. Start with the cabinet frames, using a high-quality brush for smaller areas and a foam roller for larger surfaces. Some primers recommend sanding before painting. Not only is there a lot to paint, but there's also the matter of picking out the best hardware. By

Pressed wood furniture is composed of particle board finished with a veneer to give it the appearance of solid wood. If you’re using your old hardware, you can clean it or refinish it with spray paint for a new look. The topcoat with two coats of 100% acrylic paint. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply. Wipe or vacuum surfaces to clean off the sanding dust. The laminate must be in good condition for best results. On-screen and printer color representations may vary from actual paint colors.

If your cabinets were previously painted and your house was built before 1978, the paint may be lead-based. If you’re using new hardware, make sure it has the same dimensions as your existing.

The longer the paint dries, the more durable its finish will be, and the less likely it will stick during reinstallation. Resurfacing kitchen cabinets can transform the appearance of the entire kitchen and is a much more affordable solution than replacing the cabinets…

Reassemble the cabinets and hardware. Attach the handles or knobs to a piece of cardboard so they’re upright and easier to work on. Sand down all surfaces (doors as well as the inside of the cabinetry) that will be painted using a medium-grit sandpaper or a hand sander. Check the paint label on the can for specific instructions. Once everything is fully dry, you can begin replacing the hardware in your repainted cabinets and returning them to your newly refreshed kitchen. Roll on the first coat of paint in the direction of the wood grain and let it dry completely. One of the most daunting tasks of any kitchen remodel is taking a stab at trying to redo your kitchen cabinets. Once your primer is completely dry (at least 24 hours in a well-ventilated area), it’s time to sand again. Tape around all the surfaces of the cabinetry that won’t be painted and hang a plastic tarp to protect your countertop and backsplash from splatter. Wipe away any dust with a slightly damp cloth, then let dry. With latex paints, always follow the manufacturer’s instructions regarding cure time. Now that your cabinets are painted, consider adding shelf liners. Because pressed wood furniture does not accept stain well, you should refinish it with enamel instead. It’s pretty amazing how a single can of paint can transform a space, and when it comes to your kitchen in particular, it might be the most budget-friendly yet impactful tool you can use in DIY renovation. Painting cabinets will take several days to complete, so plan accordingly. Make sure you’ll have proper ventilation there too.

it can brighten up an otherwise dim space. Sand a third and final time with 220-grit sandpaper. Apply a second coat of paint. Use painter’s tripods to lift the doors and drawers up from your painting surface. Its purpose is to cover the surface and provide a good base for the finish paint.